Time to bust out your craft supplies because it’s HALLOWEEN! After much back and forth with J, she finally settled on a costume…a black cat. She was also very specific in her requirements for the costume: pink collar with crystals, black paws with white pads, white whiskers on a black mask and a white patch on her chest. While you may commend her for her specificity since she’s only 4 1/2, I can’t give her much credit. There is a picture collage of her first year of life hanging in her room. In it is her first Halloween costume. Guess what it is? Yup.
I decided to make the mask and a few other parts of her costume. I came up with this mask to avoid putting paint on her face. Of course, if your kid doesn’t like wearing masks, then you’ll need a new plan…or costume.
J also decided that I need to be a black cat too. BONUS: The pattern fit my face too, with a slight increase the size of the eye holes. Easy as long as you’re not scissor-phobic. A few extra snips and you should be able to see out of the mask.
Here is what you’ll need to make the mask:
- Cat mask pattern (download and print the PDF)
- Black felt (a felt square from the craft store is more than you need)
- White pipe cleaners (minimum 4)
- Black elastic
- Hot glue gun
- Straight pins (optional, but really helpful)
- Needle and thread (optional, but again, helpful)
Print out the cat mask pattern at 100%. I included a 1″ line in case you’re not sure if the pattern is the correct size when printed. The pattern is HALF of the mask. Cut it out of the paper and don’t forget to cut out the eye holes. Fold your felt piece in half and place the pattern on it, with the side where I wrote “fold” lined up over the fold.
The little circle on the pattern indicates where to attach your elastic. We’ll get to that in a minute.
Here’s where the pins come in very handy. Pin around the pattern so it won’t slip while you’re cutting it.
Cut around the outside of the mask. Then cut out the eye holes. This part is a little tricky, but you can handle it! If you mess up, you probably have enough black felt to try one more time.
After the felt is cut, hold it up to your child’s face (or your own) and make sure they can see and breath.
Time for the big guns, err, hot glue gun. Fold your pipe cleaners in half and place them on the mask approximately where you want them. I opted for symmetry but you may not be so type-A.
Glue the folded end of the pipe cleaner to the mask. Repeat for all of the whiskers. Once the glue is dry you need to adhere the whiskers to the outer edges of the mask, otherwise they will bop around, sag, and generally look bad. Glue them to the side of the mask or tack them with the needle and thread. Either way will work. I tacked J’s mask since it was the first one I made. I made mine afterwards and used glue because I was getting lazy.
IMPORTANT!! Check the length of the whiskers. Cut them if need be. Then DON’T SKIP THIS STEP. Put a small bead of hot glue at the cut end of each whisker so that the wire isn’t so sharp and pokey. Once the glue has cooled slightly, use your finger to smoosh it into the wire. Whiskers are not weapons!
Almost done! Grab your elastic and pin it to the mask. Use the circle on the pattern for a point of reference. Again, straight pins will come in handy but not absolutely necessary. Use a safety pin if you have one. Adjust the length of the elastic as needed to fit comfortably around your child’s head.
I sewed the elastic to the mask to make sure it wouldn’t come apart when we went to Brick-or-Treat at Legoland. If you’re in a hurry, you could use hot glue. By the way, I’m a hot mess when it comes to hot glue. I burned myself several times making the mask and cat gloves.
Anyhoo, J absolutely loves her mask and the other pieces of her costume that I made and bought. In fact, she helped make her collar. She meticulously lined up all of the crystals and glued them individually. The fruit doesn’t fall far from the tree!